LG CodeZero A9 Series Service Manual Download Page 8

Page: 8 / 104

-8-

Only training and service purposes

Vacuum features

1. The product has a high level of suction power, which can be adjusted according to the

area to be cleaned.

Strong suction powered by an inverter motor can be adjusted using the Suction Control

button according to the area to be cleaned.

2. Featuring an anti-tangle power nozzle
Removes ultrafine dust.
3. Featuring dual lithium batteries (for applicable models only)
Two long-life lithium batteries eliminate the need to recharge during cleaning. Based on

the Standard mode, each battery can be used for approximately 40 minutes when fully

charged, allowing up to approximately 80 minutes cleaning.

4. Wireless type vacuum
A wireless type vacuum solves problems related to limited cord length.

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands