LG 22LY560M Commercial Mode Setup Manual Download Page 76

Page: 76 / 84

206-4261

Reference: Pillow Speaker Setup

The pillow speaker will only be functional after the Express Script/Custom Master TV Setup and/or

cloning procedures are complete.

Note:

When Installer Menu item 027 HOSPITAL MODE is set to 254 (factory default value), there is no

power (voltage) supplied to the pillow speaker.

TV ON/OFF

CHAN UP/DATA IN

COMMON

AUDIO OUT

CHAN DOWN

ON/OFF

CHAN

DOWN

CHAN

(MALE

PLUG)

VOLUME CONTROL

SPKR

Connecting a Pillow Speaker to the TV

Connect the pillow speaker (see example at right) to the PILLOW

SPEAKER interface on the rear jack panel of the TV.

Caution: Use a pillow speaker that is a UL recognized

pendant control bearing the warning: “Risk of fire if used in

oxygen enriched atmosphere. Keep pendant control away

from oxygen equipment.”

Controlling the TV with Serial Data

These TV models are capable of being controlled by a single-wire, serial

data signal. This is an LG patented technology and is being implemented

by certain brands of “smart” pillow speakers.

Pillow Speaker Interface

This connector provides an interface for patient-pendant remote control

or entertainment audio and nurse call systems. All lines are isolated

from the AC power line. (Optoisolators isolate the control lines, and a

transformer isolates the audio.) Earth ground is provided on pin 4

(Common) in the default configuration (e.g., for Zenith/Philips pillow

speakers). For negative voltage configuration (e.g., for RCA pillow

speakers), +5 volts is provided on pin 4 (Common), with pin 3 (Channel

Up/Data In) referenced to ground.
The following table describes the pillow speaker interface pinout (see

also diagram at right).

Pin No.

Description

Analog external control for TV ON/OFF.

No connection

Analog external control for Channel Up or Serial Data In.

Common connection for control, data, and audio output.

Isolated Audio Output. Nominal 14 ohm source impedance with

short circuit protection. Intended for a pillow speaker with a low-

impedance, pad-type volume control.

Analog external control for Channel Down.

Controlling the TV with Mechanical Switches

A typical analog pillow speaker with mechanical switches will momentarily

connect pin 1, 3, or 6 to pin 4 (Common) to control Power ON/OFF,

Channel Up, or Channel Down (see schematic at right). These pins are at

+13 volts DC (when measured from pin 4) with the switches open. Typical

current draw is 8 mA when a switch is closed. (This operation is identical

to previous models using the 5-wire interface, except that only +7 volts

DC was supplied and current draw was only 2.5 mA.)

PILLOW SPEAKER

CHANNEL

VOLUME

POWER

MUTE

OPTION

SLEEP

PREV

Typical Pillow Speaker

(Serial Data Control)

Typical Schematic for

Analog Pillow Speaker

Pillow Speaker Interface Pinout

Summary of Contents for 22LY560M





















































































Search results

Summary of Contents for 22LY560M

Reviews:

Related manuals for 22LY560M

Brands by name

Popular brands

LG 22LY560M, Commercial Mode Setup Manual

Search results

Summary of Contents for 22LY560M

Reviews:

Related manuals for 22LY560M

Brands by name

Popular brands