Lexmark 7000 Color Jetprinter Service Manual Download Page 39

Page: 39 / 85

4-3

4092

Base Assembly Removal

1. Remove the front cover.

2. Remove the rear cover.

3. Disconnect the power supply connector at the system board.

4. Remove the two screws from the maintenance station

assembly. Pull up the right side of the mid frame assembly and
pull forward and remove the maintenance station assembly.

5. Remove the two screws securing the carrier frame to the base

cover.

6. Slide the printer off the base cover.

Carrier Belt Removal

1. Remove the front cover.

2. Remove the printhead carrier assembly.

3. Push the idler pulley to the right to release the tension on the

belt and remove the belt.

Note: When reinstalling the carrier belt, place the carrier at the
center position between the tabs on either end of the belt.

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands