Lexmark 7000 Color Jetprinter Service Manual Download Page 55

Page: 55 / 85

4-19

4092

Printhead Carrier Assembly Removal

1. Remove the front cover.

2. Unlock the three printhead cable connectors and disconnect the

printhead cable from the system board.

3. Remove the screws from the ends of the carrier guide rod and

move the carrier to the left.

4. Remove the carrier guide rod by lifting the right end of the rod

while spreading the right side of the carrier frame.

5. Remove the carrier assembly by lifting upward, taking care to

clear the encoder strip before pulling the carrier assembly out.

Printhead Rubber Backer Removal

1. Remove the front cover.

2. Remove the printhead carrier assembly.

3. Separate the cradle from the printhead carrier assembly by

pushing out the cradle latches [A].

4. Remove the rubber backer and paper deflector from under the

printhead carrier cable. Note: Use the illustration to assemble
the carrier parts in the correct sequence.

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands