Lexmark 7000 Color Jetprinter Service Manual Download Page 34 | Manualshive

Page: 34 / 85

background image

Diagnostic Aids 3-5

4092

Parallel Port Test

This test performs a wrap around test between the printer parallel
port and the parallel port test connector.

This test requires a parallel port wrap plug. Install the wrap plug in
the parallel port and move the jumper to pins (1 & 2) on the test
connector, before you start the test.

To run the test:

1. Turn the printer off.

2. Attach the wrap plug to the parallel port.

3. Place a two pin jumper on pins (1 & 2) of test connector J6.

4. Turn the printer on.

If the lights blink alternately, the test is failing. If the Busy Light stays
on and the Power Light blinks, the test is working properly. If the
Busy Light blinks intermittently, an intermittent failure is occurring.

«
...
32
33
34
35
36
...
»

Summary of Contents for 7000 Color Jetprinter






















































































Reviews:

No comments

Related manuals for 7000 Color Jetprinter

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 750

ImageCLASS 2300

Brand: Canon Pages: 8

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 750

Color imageCLASS 8180c

Brand: Canon Pages: 95

Brand: Canon Pages: 4

Brand: Canon Pages: 49

ImageCLASS 2300

Brand: Canon Pages: 156

Brand: Canon Pages: 193

Brand: QMS Pages: 24

imageCLASS D1120

Brand: Canon Pages: 36

ImageCLASS 2300

Brand: Canon Pages: 44

Brand: Canon Pages: 66

Brand: Olympus Pages: 71

Brand: Panasonic Pages: 102

Brand: oliser Pages: 6

Brand: Oki Pages: 215

DC240 - DocuColor 240 Color Laser

Brand: Xerox Pages: 2

ColourLaser series guide

Brand: Xante Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands