Lexmark 7000 Color Jetprinter Service Manual Download Page 23

Page: 23 / 85

2-10

4092

Paper Path Service Check

Examine the printer for the following before you begin this service
check:

•

Check the entire paper path for obstructions.

•

Be sure the paper guides are not worn or broken and are posi-
tioned against the paper without binding or buckling the paper.

•

Be sure the correct type of paper is being used.

•

Be sure the printer is installed on a flat surface.

FRU

Action

Large and Small
Feed Rollers

Check for wear and binds.

Small Feed Roller
Springs
Paper Guide
Paper Flap

Check for damage.

Exit Roller
Star Rollers
Exit Drive Belt

Check for wear and binds.

Sheet Feeder

Check the following for wear or damage:

• Pick Rollers
• Envelope Bucklers
• All parts inside the left and right edge guides.

End-of-Forms
Flag & Spring

Check for binds or damage.

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands