Lexmark 7000 Color Jetprinter Service Manual Download Page 11 | Manualshive

Page: 11 / 85

background image

General Information 1-1

4092

1. General Information

The Lexmark Color Jetprinter

TM

Series 7000, 7200 & 7200V

(Machine Type 4092) printers are personal, near laser-quality inkjet
printers. The print cartridges contain single-unit customer-
replaceable supply items. Dual printheads provide color and true
black printing without changing printheads. The black cartridge has
a total of 208 nozzles and installs on the left. The color cartridge has
a total of 192 nozzles and installs on the right. These printers are
capable of printing in two directions from either cartridge.

Operator Panel

Resolution and Print Speed

Buttons

Lights

Left Button - Power On/Off

Left Light
• Steady - Power On
• Blinking - Printer Error

Right Button - Paper Feed
Clears a paper jam or loads paper
when there is a paper out
condition.

Right Light
• Steady - Busy
• Blinking - Paper Out/Jam

Alternating Blinking Lights:
Printheads are in the load position or
printheads are installed incorrectly.

Color

Black

600 X 600 Letter Quality
1200 X1200 Ultra High Quality

600 X 600 Letter Quality
1200 X 1200 Ultra High Quality

1.4 page/minute Normal Quality
0.9 page/minute High Quality

3 page/minute Letter Quality
6.5 page/minute Draft

«
...
9
10
11
12
13
...
»

Summary of Contents for 7000 Color Jetprinter






















































































Reviews:

No comments

Related manuals for 7000 Color Jetprinter

Brand: Xerox Pages: 89

Brand: Pantum Pages: 115

TELEIOS GRANDE G5

Brand: d.gen Pages: 14

Brand: Oce Pages: 222

Brand: Partner Pages: 34

Brand: Partner Pages: 81

Ecosys FS-C5300DN

Brand: Kyocera Pages: 35

Brand: Pantum Pages: 164

Brand: SPRT Pages: 14

Brand: Ricoh Pages: 269

Brand: Graphic Products Pages: 28

Brand: DNP Pages: 93

Brand: Magicard Pages: 42

Brand: Ultimaker Pages: 9

Brand: Oce Pages: 66

Brand: RAYSHAPE Pages: 41

Brand: OKIDATA Pages: 39

Brand: Konica Minolta Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands