Lexmark 7000 Color Jetprinter Service Manual Download Page 17

Page: 17 / 85

2-4

4092

Symptom Tables

Locate the symptom in the following tables and take the appropriate
action.

Carrier Transport Problems

Communications Problems

Maintenance Station Problems

Operator Panel Problems

Symptom

Action

• No carrier movement
• Slow carrier movement
• Carrier stops
• Carrier slams side frame

Go to the

“Transport Service Check”

on page 2-15

Symptom

Action

Printer not communicating with
host computer

Go to the

“Parallel Port Service

Check” on page 2-11

Symptom

Action

• Fails to cap the printhead
• Fails to clean the printhead

Go to the

“Maintenance Station

Service Check” on page 2-7

Symptom

Action

Paper feed button does not
operate

Replace the system board.

Busy light does not come on

Replace the system board.

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands