Lexmark 7000 Color Jetprinter Service Manual Download Page 41

Page: 41 / 85

4-5

4092

Note: During reassembly:

1. Be sure the small feed roll spring extensions [B] are in the

grooves of the small feed roll arms.

2. Be sure the short extensions of the two paper flap springs are

trapped under the carrier frame [C].

3. Be sure the tab from the paper guide does not deflect the small

feedroll shaft downward. The shaft should be forward of the tab.

Carrier Transport Motor Removal

1. Remove the front cover.

2. Disconnect the transport motor connector from the system

board.

3. Remove the belt from the transport motor pulley.

4. Remove the two screws securing the transport motor to the

carrier frame and remove the motor. Note the routing of the
motor cable.

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands