Lexmark 7000 Color Jetprinter Service Manual Download Page 62

Page: 62 / 85

Preventive Maintenance 6-1

6. Preventive Maintenance

This chapter contains the lubrication specifications. Follow these
recommendations to prevent problems and maintain optimum
performance.

Lubrication Specifications

Lubricate only when parts are replaced or as needed, not on a
scheduled basis. Use grease P/N 99A0394 to lubricate the following:

•

All gear mounting studs.

•

The left and right ends of the large feed roller at the side frames.

•

Both ends of the sheet feeder pick roll shaft at the side frames.

•

The carrier to carrier frame engagement.

•

The carrier guide rod, and carrier guide rod bearings.

•

Both ends of the exit roller shaft.

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands