Lexmark 7000 Color Jetprinter Service Manual Download Page 16

Page: 16 / 85

Diagnostic Information 2-3

4092

If your printer completes POST with no errors, go to the

“Symptom

Tables” on page 2-4

, locate the symptom and take the indicated

action.

If your printer does not complete POST, locate the symptom in the
following table and take the indicated action.

POST Symptom Table

Symptom

Action

No Power light
and no motors
run

Go to the

“Power Service Check” on page 2-11

Feeds paper

Go to the

“First Print Line Service Check” on page 2-6

Paper feed
gears do not
turn

Go to the

“Paper Feed Service Check” on page 2-8

Carrier doesn’t
move

Go to the

“Transport Service Check” on page 2-15

Carrier slams
side frame

Go to the

“Transport Service Check” on page 2-15

Summary of Contents for 7000 Color Jetprinter






















































































Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands

Lexmark 7000 Color Jetprinter, Service Manual

Search results

Summary of Contents for 7000 Color Jetprinter

Reviews:

Related manuals for 7000 Color Jetprinter

Brands by name

Popular brands