manualshive.com logo in svg

Leuze electronic AMS 338i, Technical Description, Page: 47 / 96

Share
Download
Leuze electronic AMS 338i Technical Description Download Page 47

Display and control panel AMS 338i

44

AMS 338

i

Leuze electronic

8.3

Menu description

8.3.1

The main menus

After voltage has been applied to the laser, device information is displayed for several
seconds. The display then shows the measurement window with all status information.

 

AMS 338i 120
Leuze electronic

GmbH & Co. KG

SW: V 1.3.0

HW:1

SN: ---------------

Device information - main menu

This menu item contains detailed information on
• Device model,
• Manufacturer,
• Software and hardware version,
• Serial number.
No entries can be made via the display.

Network information
Address:

1

Alias:

1

Status:

INIT, PRE, SAFE, O

P

Network information - main menu

• Explanations of address, alias, status.
No entries can be made via the display.

IO1

LSR

PLB

ECAT

IO2 TMP

ATT

ERR

+ 87.000m

Status and measurement data - main menu

• Display of status-, warning-, and error messages
• Status overview of the switching inputs/outputs.
• Bar graph for the reception level.
• Link.
• Measurement value.
No entries can be made via the display. 
See "Indicators in the display" on page 39..

Parameter

Parameter handling
EtherCAT
Maximum position value
I/O
Other

Parameter - main menu

• Configuration of the AMS.
See "Parameter menu" on page 45.

Language 
selection
o Deutsch
o English
o Español
o Français

Language selection - main menu

• Selection of the display language.
See "Language selection menu" on page 48.

Service

Status messages
Diagnostics
Expanded diagnostics

Service - main menu

• Display of status messages.
• Display of diagnostic data.
No entries can be made via the display.
See "Service menu" on page 49.

Summary of Contents for AMS 338i

































































































Reviews:

No comments