Lenovo ThinkSystem ST650 V2 Reference Download Page 75

Page: 75 / 210

SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0088

User Action:

Information only; no action is required.

•

FQXSPNM4046I: LAN over USB [arg1] by user [arg2].

A user configured USB-LAN

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0089

User Action:

Information only; no action is required.

•

FQXSPNM4047I: LAN over USB Port Forwarding set by user [arg1]: ExternalPort=[arg2], USB-LAN

port=[arg3].

A user configured USB-LAN port forwarding

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0090

User Action:

Information only; no action is required.

•

FQXSPNM4048I: PXE boot requested by user [arg1].

PXE boot requested

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0129

User Action:

Information only; no action is required.

•

FQXSPNM4049I: User [arg1] has initiated a TKLM Server Connection Test to check connectivity to

server [arg2].

User initiated a TKLM Server Connection test.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:

Chapter 2

XClarity Controller events

Summary of Contents for ThinkSystem ST650 V2



















































































































































































































Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Related manuals for ThinkSystem ST650 V2

Brands by name

Popular brands

Lenovo ThinkSystem ST650 V2, Reference

Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Related manuals for ThinkSystem ST650 V2

Brands by name

Popular brands