Lenovo ThinkSystem ST650 V2 Reference Download Page 88

Page: 88 / 210

User Action:

Information only; no action is required.

•

FQXSPPP4029I: The server was automatically powered on because the power restore policy is set

to restore previous power state..

Server was automatically powered on because the power restore policy is set to restore previous power
state.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0173

User Action:

Information only; no action is required.

•

FQXSPPP4030I: The server was reset via Platform Event Filter.

Server was reset via Platform Event Filter

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0174

User Action:

Information only; no action is required.

•

FQXSPPP4031I: The server was power-cycled via Platform Event Filter.

Server was power-cycled via Platform Event Filter

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0175

User Action:

Information only; no action is required.

•

FQXSPPP4032I: The server was soft reset.

Server was soft reset

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0176

User Action:

ThinkSystem ST650 V2 Messages and Codes Reference

Summary of Contents for ThinkSystem ST650 V2



















































































































































































































Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Related manuals for ThinkSystem ST650 V2

Brands by name

Popular brands

Lenovo ThinkSystem ST650 V2, Reference

Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Related manuals for ThinkSystem ST650 V2

Brands by name

Popular brands