manualshive.com logo in svg

Lenovo ThinkSystem ST650 V2, Reference

Share
Download
Lenovo ThinkSystem ST650 V2 Reference Download Page 135

This message is for the use case when an implementation has detected that the Firmware or Software 
Changed.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 
CIM Prefix: PLAT CIM ID: 0438

User Action:

Information only; no action is required.

• 

FQXSPUP0007L: Invalid or Unsupported firmware or software was detected on system 

[ComputerSystemElementName]. 

This message is for the use case when an implementation has detected an Invalid/Unsupported Firmware/ 
Software Version.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0446

User Action:

Reflash or update XCC firmware.

• 

FQXSPUP4000I: Please ensure that the Management Controller [arg1] is flashed with the correct 

firmware. The Management Controller is unable to match its firmware to the server. 

This message is for the use case where a Management Controller firmware version does not match the 
server.

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0031

User Action:

Complete the following steps until the problem is solved:  

1.  Update the BMC firmware. 

2.  NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device 

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution 
before you update the code.

3.  If problem persists, collect Service Data log.

4.  Contact Lenovo Support.

• 

FQXSPUP4001I: Flash of [arg1] from [arg2] succeeded for user [arg3] . 

This message is for the use case where a user has successfully flashed the firmware component (MC Main 
Application, MC Boot ROM, BIOS, Diagnostics, System Power Backplane, Remote Expansion Enclosure 
Power Backplane, Integrated System Management).

Chapter 2

.

XClarity Controller events

131

Summary of Contents for ThinkSystem ST650 V2



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands