Lenovo ThinkSystem ST650 V2 Reference Download Page 29

Page: 29 / 210

User Action:

Complete the following steps until the problem is solved:

1. Update the BMC firmware.

2. NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.

3. If problem persists, collect Service Data log.

4. Contact Lenovo Support.

•

FQXSPBR4002I: Management Controller [arg1] Reset was caused by restoring default values.

This message is for the use case where a Management Controller has been reset due to a user restoring
the configuration to default values.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0032

User Action:

Information only; no action is required.

•

FQXSPBR4003I: Platform Watchdog Timer expired for [arg1].

This message is for the use case when an implementation has detected a Platform Watchdog Timer
Expired

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - OS Timeout
SNMP Trap ID: 21
CIM Prefix: IMM CIM ID: 0039

User Action:

Complete the following steps until the problem is solved:

1. Reconfigure the watchdog timer to a higher value.

2. Make sure that the BMC Ethernet-over-USB interface is enabled.

3. Reinstall the RNDIS or cdc_ether device driver for the operating system.

4. Disable the watchdog timer.

5. Check the integrity of the installed operating system.

6. If problem persists, collect Service Data log.

7. Contact Lenovo Support.

•

FQXSPBR4004I: Server timeouts set by user [arg1]: EnableOSWatchdog=[arg2],

OSWatchdogTimout=[arg3], EnableLoaderWatchdog=[arg4], LoaderTimeout=[arg5].

A user configures Server Timeouts

Severity: Info
Serviceable: No
Automatically notify Support: No

Chapter 2

XClarity Controller events

Summary of Contents for ThinkSystem ST650 V2



















































































































































































































Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Related manuals for ThinkSystem ST650 V2

Brands by name

Popular brands

Lenovo ThinkSystem ST650 V2, Reference

Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Related manuals for ThinkSystem ST650 V2

Brands by name

Popular brands