Lenovo ThinkSystem ST650 V2 Reference Download Page 147

Page: 147 / 210

4. Contact Lenovo Support.

•

FQXSFDD0006M: DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.

Severity: Warning

User Action:

Complete the following steps:

1. Reboot the system.

2. Reflash the adapter firmware.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFDD0007G: Security Key Lifecycle Manager (SKLM) IPMI Error.

Severity: Warning

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to

this error.

2. A/C cycle the system.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFIO0005I: An intra-board UPI has been disabled on the link between processor [arg1] port

[arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.

Severity: Info

User Action:

Complete the following steps:

1. This event should be followed by a recent FQXSFIO0005M / FQXSFIO0006M event denoting some

UPI links failure which caused UPI topology downgrade.

2. Solve the event FQXSFIO0005M / FQXSFIO0006M at first, then this event should be solved

automatically.

3. If no recent or after fixing FQXSFIO0005M / FQXSFIO0006M event, this event still persists, collect

Service Data logs.

4. Contact Lenovo Support.

•

FQXSFIO0005M: An intra-board UPI failure has been detected on the link between processor [arg1]

port [arg2] and processor [arg3] port [arg4].

Severity: Error

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

error.

2. If the problem persists, collect Service Data logs.

3. Contact Lenovo Support.

•

FQXSFIO0006I: An inter-board UPI has been disabled on the link between processor [arg1] port

[arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.

Chapter 3

UEFI events

143

Summary of Contents for ThinkSystem ST650 V2



















































































































































































































Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem ST650 V2, Reference

Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Brands by name

Popular brands