Lenovo ThinkSystem ST650 V2 Reference Download Page 172

Page: 172 / 210

7. Contact Lenovo Support.

•

FQXSFPU0033G: Processor has been disabled.

Severity: Warning

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to

this error.

2. Reboot the system.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFPU0034L: The TPM could not be initialized properly.

Severity: Error

User Action:

Complete the following steps:

1. Reboot the system. Reflash UEFI image.

2. If the problem persists, collect Service Data logs.

3. Contact Lenovo Support.

•

FQXSFPU0035N: A 3-strike timeout has occurred on processor [arg1].

Severity: Fatal

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to

this error.

2. Reboot the system.

3. Check and reverse any recent changes to system settings or the Operating System.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

•

FQXSFPU4033F: TPM Firmware recovery is in progress. Please DO NOT power off or reset system.

Severity: Warning

User Action:

Information only; no action is required.

Note:

The system will not respond to power off signal (FQXSFPU4034I) while TPM firmware recovery in

progress.

•

FQXSFPU4034I: TPM Firmware recovery is finished, rebooting system to take effect.

Severity: Info

User Action:

Information only; no action is required.

•

FQXSFPU4035M: TPM Firmware recovery failed. TPM chip may be damaged.

Severity: Warning

168

ThinkSystem ST650 V2 Messages and Codes Reference

Summary of Contents for ThinkSystem ST650 V2



















































































































































































































Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem ST650 V2, Reference

Search results

Summary of Contents for ThinkSystem ST650 V2

Reviews:

Brands by name

Popular brands