Lenovo ThinkSystem SR650 V2 Reference Download Page 87

Page: 87 / 212

Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0252

User Action:

Information only; no action is required.

•

FQXSPPP4050I: Management Controller [arg1] reset was initiated to activate PFR Firmware.

Management Controller reset was initiated to activate PFR Firmware.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0253

User Action:

Information only; no action is required.

•

FQXSPPR0001I: [ManagedElementName] detected as absent.

This message is for the use case when an implementation has detected a Managed Element is Absent.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0392

User Action:

Complete the following steps until the problem is solved:

1. Reinstall the VGA/front panel connector and cable.

2. If the problem persists, contact Lenovo Support.

•

FQXSPPU0001N: An Over-Temperature Condition has been detected on [ProcessorElementName].

This message is for the use case when an implementation has detected an Over-Temperature Condition
Detected for Processor.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Temperature
SNMP Trap ID: 0
CIM Prefix: PLAT CIM ID: 0036

User Action:

Complete the following steps until the problem is solved:

1. Check the XCC event log for any fan or cooling related issues and address them first.

2. Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are

correctly installed in place and keep clean.

3. Make sure that the room temperature meets operating specifications.

4. Upgrade all system firmware and chassis firmware (if applicable) to the latest level.

Chapter 2

XClarity Controller events

Summary of Contents for ThinkSystem SR650 V2





















































































































































































































Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands

Lenovo ThinkSystem SR650 V2, Reference

Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands