Lenovo ThinkSystem SR650 V2 Reference Download Page 130

Page: 130 / 212

Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0530

User Action:

Complete the following steps until the problem is solved:

1. Check Lenovo Support (http://support.lenovo.com/) for an applicable service bulletin or firmware

update that applies to this error.

2. If the problem persists, collect service data log from the XCC WebGUI and contact Lenovo Support.

•

FQXSPUN0026I: Device [LogicalDeviceElementName] has been added.

This message is for the use case when an implementation has detected a Device was inserted.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0536

User Action:

Information only; no action is required.

•

FQXSPUN0050M: The RAID controller in PCI slot [arg1] is in critical state. At least one logical drive

is offline.

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0522

User Action:

Complete the following steps until the problem is solved:

1. Check if the configured drives are present and they are properly connected.

2. Go to system setup and check if the devices are displayed in UEFI/XCC.

3. Ensure that the drives are spun-up and have power supplied to them.

4. If there is a backplane, check the connectors to ensure that power is being supplied to the drives.

5. If the problem persists, collect service data log from the XCC WebGUI and contact Lenovo Support.

•

FQXSPUN0053M: The RAID controller in PCI slot [arg1] is in critical status. At least one physical

drive is failed.

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Other

126

ThinkSystem SR650 V2 Messages and Codes Reference

Summary of Contents for ThinkSystem SR650 V2





















































































































































































































Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands

Lenovo ThinkSystem SR650 V2, Reference

Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands