Lenovo ThinkSystem SR650 V2 Reference Download Page 195

Page: 195 / 212

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Retry the test.

4. If the problem persists, please contact technical support.

•

FQXPMSD0005M: self-test completed having the servo (and/or seek) test element of the test failed.

Severity: Error

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Retry the test.

4. If the problem persists, please contact technical support.

•

FQXPMSD0006M: self-test completed having the read element of the test failed.

Severity: Error

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Retry the test.

4. If the problem persists, please contact technical support.

•

FQXPMSD0007M: Hard Drive(s) not found

Severity: Error

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Verify that the same Error is present in BMC or OneCLI inventory log.

4. Retry the test.

5. If the problem persists, please contact technical support.

•

FQXPMSD0008M: UEFI is not ready for LXPM to send command to test hard drive.

Severity: Error

User Action:

1. Reboot system and run the test again.

2. If this message is still reported, please run the latest version of SMART tool on OS which is open

source tool and could be downloaded from website to check hard drive status.

3. If the problem persists, please contact technical support.

•

FQXPMSD0009M: Device error is occurred when LXPM send command to test hard drive.

Chapter 4

XClarity Provisioning Manager events

191

Summary of Contents for ThinkSystem SR650 V2





















































































































































































































Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands

Lenovo ThinkSystem SR650 V2, Reference

Search results

Summary of Contents for ThinkSystem SR650 V2

Reviews:

Related manuals for ThinkSystem SR650 V2

Brands by name

Popular brands