manualshive.com logo in svg

Lenovo ThinkServer TD350, User Manual And Hardware Maintenance Manual

Share
Download
Lenovo ThinkServer TD350 User Manual And Hardware Maintenance Manual Download Page 63

14

SATA connector 0 (ports 0–3)

15

SATA connector 1(ports 4–7)

Used to connect the SATA signal cable from the system board to the Lenovo ThinkServer RAID 110i
AnyRAID Adapter.

16

Front panel connector

Used to connect the front panel cable.

17

Optical-drive 2 signal connector

Used to connect the signal cable of the second optical drive if the server has two optical drives installed.

18

RAID upgrade key connector

Used to install a RAID upgrade key.

19

Optical-drive 1 signal connector

Used to connect the signal cable of the optical drive.

20

TPM connector

Used to connect a ThinkServer Trusted Platform Module (TPM), which is a security chip, to enhance server
security. See “Installing or removing the ThinkServer Trusted Platform Module” on page 110.

21

TSM Premium connector

Used to connect a server option named ThinkServer System Manager Premium (TSM Premium) module to
enable advanced remote management functions on your server. See “Installing or removing the ThinkServer
System Manager Premium module” on page 106.

22

I2C to I2C connector

Used to connect to the I2C connector on the PCIE interposer card.

Chapter 3

.

Product overview

49

Summary of Contents for ThinkServer TD350



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands