manualshive.com logo in svg

Lenovo ThinkServer TD350, User Manual And Hardware Maintenance Manual

The Lenovo ThinkServer TD350 offers powerful performance and reliability for businesses. With our user-friendly interface, accessing the User Manual and Hardware Maintenance Manual is quick and easy. Download these essential manuals for free at manualshive.com, ensuring you have the necessary resources to maximize your server's potential.

Share
Download
background image

9. Align the holes in the drive tray with the corresponding ones on the new easy-swap drive. Then, install

the four screws to secure the drive to the drive tray.

Figure 93. Installing the drive to the drive tray

10. Slide the new easy-swap drive into the drive bay from the front until it snaps into position, and then

close the handle.

Figure 94. Installing the easy-swap drive

11. Close the front door (if available).

12. Do one of the following:

• If you are installing an easy-swap drive, save the removed dummy tray in case that you later remove

the easy-swap drive and need a dummy tray to cover the drive bay.

• If you are replacing an easy-swap drive and are instructed to return the old easy-swap drive, follow all

packaging instructions and use any packaging materials that are supplied to you for shipping.

Chapter 6

.

Replacing hardware

135

Summary of Contents for ThinkServer TD350



































































































































































































































Reviews:

No comments

Related manuals for ThinkServer TD350

NEC Univerge SV9300 Programming Manual preview
Univerge SV9300
Brand: NEC Pages: 47
NEC Univerge SV9100 Manual preview
Univerge SV9100
Brand: NEC Pages: 766
Sybase Adaptive Server IQ 12.4.2 Administration And Performance Manual preview
Adaptive Server IQ 12.4.2
Brand: Sybase Pages: 536
IBM iDataPlex dx320 6385 User Manual preview
iDataPlex dx320 6385
Brand: IBM Pages: 60
H3C UniServer R4900 G3 Quick Start Manual preview
UniServer R4900 G3
Brand: H3C Pages: 24
Supermicro SSG-927R-E2CJB User Manual preview
SSG-927R-E2CJB
Brand: Supermicro Pages: 62
Supero SUPERSERVER 5018D-MF User Manual preview
SUPERSERVER 5018D-MF
Brand: Supero Pages: 120
Fujitsu GP 7000F Manual preview
GP 7000F
Brand: Fujitsu Pages: 200
LG 27CN650N Owner'S Manual preview
27CN650N
Brand: LG Pages: 100
LG 24CN650N Owner'S Manual preview
24CN650N
Brand: LG Pages: 35
BITMAIN S4+ Manual preview
S4+
Brand: BITMAIN Pages: 10
EVS XT nano Hardware Technical Reference Manual preview
XT nano
Brand: EVS Pages: 70
Promise Technology SmartStor Zero Quick Start Up Manual preview
SmartStor Zero
Brand: Promise Technology Pages: 2
Cooper Bussmann BU-945U-E User Manual preview
BU-945U-E
Brand: Cooper Bussmann Pages: 82
C-MOR IP Video Surveillance User Manual preview
IP Video Surveillance
Brand: C-MOR Pages: 62
BayTech LASERSHARE PS-MIO Owner'S Manual preview
LASERSHARE PS-MIO
Brand: BayTech Pages: 133
3Com EtherLink Quick Start Manual preview
EtherLink
Brand: 3Com Pages: 65
Intel S2600CO series User Manual preview
S2600CO series
Brand: Intel Pages: 167

Brands by name

Popular brands

Load more brands