Lenovo ThinkServer TD350 User Manual And Hardware Maintenance Manual Download Page 175

Page: 175 / 226

• For 2.5-inch-drive server models that have an AnyRAID adapter installed with an air duct

Loosen the screw that secures the AnyRAID-adapter air duct. Then, lift it in the direction as shown
until you can completely remove it.

Note:

The screw is an integrated part of the AnyRAID-adapter air duct. Do not try to remove the

screw from the AnyRAID-adapter air duct.

Figure 128. Removing the AnyRAID-adapter air duct for server models with 2.5-inch drives

8. Loosen the two screws that secure the AnyRAID adapter. Then, grasp the AnyRAID adapter by its edges

and carefully pull it out of the AnyRAID-adapter slots on the backplane.

Notes:

• The AnyRAID adapter fits tightly into the AnyRAID-adapter slots. If necessary, alternatively move

each side of the AnyRAID adapter a small and equal amount until it is removed from the connectors.

• The two screws are integrated parts of the AnyRAID adapter. Do not try to remove the two screws

from the AnyRAID adapter.

Figure 129. Removing the AnyRAID adapter

Chapter 6

Replacing hardware

161

Summary of Contents for ThinkServer TD350



































































































































































































































Search results

Summary of Contents for ThinkServer TD350

Reviews:

Brands by name

Popular brands

Lenovo ThinkServer TD350, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer TD350

Reviews:

Brands by name

Popular brands