manualshive.com logo in svg

Lenovo ThinkServer TD350, User Manual And Hardware Maintenance Manual

Share
Download
Lenovo ThinkServer TD350 User Manual And Hardware Maintenance Manual Download Page 151

• If you are replacing a tape drive, disconnect the power and signal cable from the rear of the tape

drive. Lift the release button

1

in the direction as shown and push the tape drive from the rear until it

is projected from the front of the chassis. Then, hold the tape drive from the front and completely
slide it out of the chassis.

Figure 96. Removing the tape drive

5. Touch the static-protective package that contains the new tape drive to any unpainted surface on the

outside of the server. Then, take the new tape drive and the cable out of the package.

6. Lift the release button

1

in the direction as shown and slide the new tape drive into the lower

optical-drive bay from the front until it snaps into position.

Figure 97. Installing the tape drive

Chapter 6

.

Replacing hardware

137

Summary of Contents for ThinkServer TD350



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands