Lenovo ThinkServer TD350 User Manual And Hardware Maintenance Manual Download Page 111 | Manualshive

Page: 111 / 226

background image

If your server has an SD module installed, do the following when you want to remove the SD module:

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Remove the cooling shroud. See “Removing the cooling shroud” on page 75.

5. Remove any parts and disconnect any cables that might impede your operation.

6. Locate the SD module on the system board.

7. Press the two release tabs

1

and grasp the SD module by its edges at the same time. Then, lift the

SD module straight up and off the system board.

Figure 58. Removing the SD module

8. Push the SD card inward a little until you hear a click. Then, the SD card ejects. Gently slide the

card out of the card slot.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the removal procedure, go to “Completing the parts replacement” on page 180.

Installing or removing the Lenovo ThinkServer RAID 110i upgrade key

The Lenovo ThinkServer RAID 110i upgrade key expands the capability of the system board by activating
RAID 5 for the onboard SATA software RAID. You can purchase a Lenovo ThinkServer RAID 110i upgrade
key (hereinafter referred to as the RAID 110i upgrade key) from the Lenovo Web site at:
http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server

Installing the RAID 110i upgrade key

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

.

Replacing hardware

97

«
...
109
110
111
112
113
...
»

Summary of Contents for ThinkServer TD350



































































































































































































































Reviews:

No comments

Related manuals for ThinkServer TD350

UniServer T1100 G3

Brand: H3C Pages: 66

UniServer R6900 G3

Brand: H3C Pages: 214

UniServer R6700 G3

Brand: H3C Pages: 151

UniServer R4900 G5

Brand: H3C Pages: 16

Brand: SEH Pages: 50

Brand: Thecus Pages: 120

WECS II 2048/DMX/02

Brand: Oase Pages: 67

Brand: BlueBroadcaster Pages: 21

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

Brand: Goonas Pages: 13

376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch

Brand: HP Pages: 169

Brand: Leightronix Pages: 22

Xtreme PC NG6450

Brand: Chip PC Pages: 4

Brand: OSD Audio Pages: 4

ProxyServer MTPSR1-100

Brand: Multitech Pages: 16

MultiArrayIII MA3a

Brand: Multitech Pages: 40

Brand: Multitech Pages: 82

DSTni-XPress DR

Brand: Lantronix Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands