Lenovo ThinkServer TD350 User Manual And Hardware Maintenance Manual Download Page 46 | Manualshive

Page: 46 / 226

background image

Power supply status LEDs

Each hot-swap power supply has three status LEDs.

1

2

3

Figure 12. Power supply status LEDs

LED

Status

Description

Action

Off

The power supply is
disconnected from the ac
power source.

No action is needed.

1

Input status LED

On, green

The power supply is connected
to the ac power source.

No action is needed.

Off

The server is off or the power
supply is not working normally.

Replace the power supply.
See “Installing or replacing a
hot-swap redundant power
supply” on page 147.

Blinking, green (about one
flash every two seconds)

The power supply is in cold
redundancy active mode.

No action is needed.

Blinking, green (about two
flashes each second)

The power supply is in cold
redundancy sleep mode.

No action is needed.

2

Output status

LED

On, green

The server is on and the power
supply is working normally.

No action is needed.

Off

The power supply is working
normally.

No action is needed.

3

Fault LED

On, amber

The power supply has failed.

Replace the power supply.
See “Installing or replacing a
hot-swap redundant power
supply” on page 147.

RAID adapter

Your server supports the following RAID adapters (supported type varies by server model):

• Lenovo ThinkServer RAID 110i AnyRAID Adapter (also called pass-through board)

• Lenovo ThinkServer RAID 510i AnyRAID Adapter

• Lenovo ThinkServer RAID 720i AnyRAID Adapter

• Lenovo ThinkServer RAID 720ix AnyRAID Adapter

• Lenovo ThinkServer RAID 520i PCIe RAID Adapter

• Lenovo ThinkServer RAID 720i PCIe RAID Adapter

You can purchase a supported RAID adapter from Lenovo and install it into your server to provides SATA/SAS
software/hardware RAID function. For a list of ThinkServer options, go to:
http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server

Note:

The option kit is designed for different types of servers and might contain additional cables that are

not required for your server.

32

ThinkServer TD350 User Guide and Hardware Maintenance Manual

«
...
44
45
46
47
48
...
»

Summary of Contents for ThinkServer TD350



































































































































































































































Reviews:

No comments

Related manuals for ThinkServer TD350

Brand: Premio Pages: 3

Brand: Atop Pages: 2

Brand: IBM Pages: 140

Brand: Ganz Pages: 5

Brand: TRENDnet Pages: 14

Brand: IBM Pages: 74

IntelliStation R Pro

Brand: IBM Pages: 194

Brand: Altos Pages: 93

TeraStation TS-RXL/R5

Brand: Buffalo Pages: 91

UCS Invicta C3124SA

Brand: Cisco Pages: 60

Brand: Cisco Pages: 54

UCS Invicta C3124SA

Brand: Cisco Pages: 40

Brand: Cisco Pages: 132

Brand: Cisco Pages: 46

Brand: Cisco Pages: 35

Brand: Cisco Pages: 188

AlphaServer GS60E

Brand: Compaq Pages: 16

AlphaServer DS20E

Brand: Compaq Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands