Lenovo IdeaCentre B310 Hardware Maintenance Manual Download Page 44 | Manualshive

Page: 44 / 64

background image

Hardware Maintenance Manual

42

5. Lift up the heatsink.

6.  Align then install the new heatsink.
7.  Align then install the motherboard cover back.
8.  Align then install the computer cover and computer stand.

Replacing the system fan

To remove the system fan:

1. Removing the computer stand. Refer to “Removing the computer

stand”.

2. Removing the computer cover. Refer to “Removing the computer

cover”.

3. Removing the motherboard cover. Refer to “Removing the

motherboard cover”.

4.  Remove the heatsink. Refer to “Replacing the heatsink”.
5.  Disconnect the power cable from the motherboard.
6.  Remove the 3 screws that secure the system fan to the chassis.

«
...
42
43
44
45
46
...
»

Summary of Contents for IdeaCentre B310

































































Reviews:

No comments

Related manuals for IdeaCentre B310

Brand: Gateway Pages: 124

Brand: Production Basics Pages: 3

SmartCraft SC5000

Brand: Mercury Pages: 64

Brand: Compaq Pages: 110

Brand: Vivo Pages: 3

Brand: Dell Pages: 3

Brand: Silicon Graphics Pages: 228

Brand: Diamond Systems Pages: 9

Brand: Renkforce Pages: 88

Brand: ROBINHOOD Pages: 10

Brand: Partner Pages: 52

Brand: AMSTRAD Pages: 51

Brand: WB Manufacturing Pages: 3

Brand: IBM Pages: 86

AIO Touch DW03437

Brand: DAWAR Pages: 10

Brand: UniSvr Pages: 30

Brand: IBM Pages: 152

Brand: Acer Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands