Lenovo IdeaCentre B310 Hardware Maintenance Manual Download Page 53 | Manualshive

Page: 53 / 64

background image

Chapter 8. Replacing hardware

51

12. Lift up the motherboard.

13. Align then screw back the TV antenna connector to the new

motherboard.

14. Align then screw in the new motherboard to the chassis.
15. Install all related components back to the new motherboard.
16. Connect all the cables to the new motherboard.
17. Screw back the motherboard cover.
18. Install the computer cover and screw back the computer stand.

Removing the shell

To remove the back shell:

1.  Remove the computer stand. Refer to “Removing the computer stand”.
2.  Remove the computer cover. Refer to “Removing the computer cover”.
3.  Remove the 5 screws that secure the shell to chassis.

«
...
51
52
53
54
55
...
»

Summary of Contents for IdeaCentre B310

































































Reviews:

No comments

Related manuals for IdeaCentre B310

Brand: Xerox Pages: 20

Brand: DATA FROM SKY Pages: 40

DECstation 316+

Brand: DEC Pages: 94

PC 300GL Type 6285

Brand: IBM Pages: 96

IntelliStation Z Pro Type 6866

Brand: IBM Pages: 194

Nuvo-8108GC Series

Brand: Neousys Technology Pages: 142

VisuNet GXP PC-GXP1100-22F

Brand: Pepperl+Fuchs Pages: 54

Brand: Dell Pages: 72

Brand: BiGDUG Pages: 3

Brand: BiGDUG Pages: 4

Brand: G-Wiz Pages: 50

Brand: Gigabyte Pages: 67

EPC PM 1700tc Nautic

Brand: LAUER Pages: 68

Jackson Desk TD2000-AC

Brand: WB Manufacturing Pages: 2

Brand: MSI Pages: 86

Brand: CyberPower Pages: 2

Brand: CyberPower Pages: 10

Brand: A’PEX Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands