Lenovo IdeaCentre B310 Hardware Maintenance Manual Download Page 48 | Manualshive

Page: 48 / 64

background image

Hardware Maintenance Manual

46

5. Remove the screw that secures the WLAN card to motherboard, and

pull out the WLAN card.

6. Align then insert the new WLAN card to the card port and screw it in

to the motherboard.

7.  Connect the antenna cables back to the new WLAN card.
8.  Install the motherboard cover back.
9.  Install the computer cover and computer stand.

Replacing the speakers system

1.  Remove the computer stand. Refer to "Removing the computer stand".
2.  Remove the computer cover. Refer to "Removing the computer cover".
3.  Remove the motherboard cover. Refer to "Removing the motherboard

cover".

4. Disconnect the cables from the motherboard.
5. Remove the 4 screws that secure the speakers system to the chassis.

«
...
46
47
48
49
50
...
»

Summary of Contents for IdeaCentre B310

































































Reviews:

No comments

Related manuals for IdeaCentre B310

Brand: Gateway Pages: 176

Brand: Aaeon Pages: 44

Power Panel 300

Brand: B&R Industries Pages: 612

Millenium Studio Desk WS20

Brand: thomann Pages: 2

OptiPlex 7440 All-In-One W11C

Brand: Dell Pages: 80

Brand: Dell Pages: 41

Optiplex 9010 All In One

Brand: Dell Pages: 67

Brand: Uplift Desk Pages: 2

RTM-ATCA-748x-40G

Brand: SMART Embedded Computing Pages: 2

Brand: Dell Pages: 2

Brand: Dell Pages: 2

Alienware Aurora R15

Brand: Dell Pages: 8

Brand: Dell Pages: 13

Brand: Dell Pages: 2

Brand: Dell Pages: 6

Brand: Dell Pages: 23

Brand: Dell Pages: 32

Brand: Dell Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands