Lenovo IdeaCentre B310 Hardware Maintenance Manual Download | Manualshive

Page: 50 / 64

background image

Hardware Maintenance Manual

48

6. Disconnect all the cables from the inverter board and slide out the

inverter board from the cover.

7.  Connect the cables to the new inverter board.
8.  Align then screw in the new inverter board.
9.  Install the optical disk drive.
10. Install the computer cover and computer stand.

Replacing the TV tuner card

To replace the TV tuner card

1.  Remove the computer stand. Refer to “Removing the computer stand”.
2.  Remove the computer cover. Refer to “Removing the computer cover”.
3.  Remove the motherboard cover. Refer to “Removing the motherboard

cover”.

4. Disconnect the antenna cable from the TV tuner card.
5. Remove the screw that secures the TV tuner card to the motherboard.

«
...
48
49
50
51
52
...
»

Summary of Contents for IdeaCentre B310

































































Reviews:

No comments

Related manuals for IdeaCentre B310

Brand: IBM Pages: 198

Brand: IBM Pages: 32

Brand: IBM Pages: 32

Brand: IBM Pages: 32

Brand: IBM Pages: 46

Brand: IBM Pages: 32

Brand: IBM Pages: 72

Brand: Radio Shack Pages: 276

Brand: C&T Solution Pages: 108

Afolux LX Series

Brand: IEI Technology Pages: 131

Brand: Roland Pages: 1

Brand: Bull Pages: 302

Brand: Gateway Pages: 144

Brand: Vivo Pages: 3

Brand: HP Pages: 122

Apollo 9000 400dl

Brand: HP Pages: 296

9000 Model D280

Brand: HP Pages: 68

A1210n - Pavilion - 512 MB RAM

Brand: HP Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands