Lenovo IdeaCentre B310 Hardware Maintenance Manual Download Page 45 | Manualshive

Page: 45 / 64

background image

Chapter 8. Replacing hardware

43

7. Slide the system fan out and lift it up to remove it.

8. Align then install the new system fan.
9. Align then install the heatsink & the motherboard cover back.
10. Align then install the computer cover and computer stand.

Replacing the microprocessor

Important

Do not touch the gold contact on the bottom of the microprocessor.
When handling the microprocessor, touch only the sides.

1.  Remove the computer stand. Refer to “Removing the computer stand”.
2.  Remove the computer cover. Refer to “Removing the computer cover”.
3.  Remove the motherboard cover. Refer to “Removing the motherboard

cover”.

4. Remove the heatsink. Refer to “Replacing the heatsink”.
5. Lift the small handle and open the retainer.

«
...
43
44
45
46
47
...
»

Summary of Contents for IdeaCentre B310

































































Reviews:

No comments

Related manuals for IdeaCentre B310

Brand: Kaypro Pages: 157

Brand: IBM Pages: 86

Brand: Saint Song Corporation Pages: 33

POWERMATE - VERSION 2007

Brand: NEC Pages: 31

Brand: Vecow Pages: 144

Brand: Omnitronic Pages: 56

Brand: Dell Pages: 77

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 29

VAIO PCG-V505DC2 Series

Brand: Sony Pages: 2

VAIO MX PCV-MXS10

Brand: Sony Pages: 1

Brand: Sony Pages: 2

VAIO E Series SVE111

Brand: Sony Pages: 2

Brand: Sony Pages: 11

VAIO PCG-TR3 Series

Brand: Sony Pages: 17

Brand: Sony Pages: 44

VAIO MX PCV-MXS10

Brand: Sony Pages: 32

VAIO PCG-TR3 Series

Brand: Sony Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands