Lenovo 7X69 Setup Manual Download Page 116

Page: 116 / 172

• SATA/SAS hard-disk drive

For a complete list of supported optional device for this server, see

https://static.lenovo.com/us/en/

serverproven/index.shtml

Before installing a 2.5-inch hot-swap drive:

1. Read the safety information and installation guidelines (see

“Safety” on page iii

and

“Installation

Guidelines” on page 56

2. Touch the static-protective package that contains the component to any unpainted metal surface on the

server; then, remove it from the package and place it on a static-protective surface.

To install a 2.5-inch drive, complete the following steps:

Watch the procedure

A video of this procedure is available at YouTube:

https://www.youtube.com/watch?v=pIb0bIyfkDY&=

PLYV5R7hVcs-Ak9fT8QAx8fLbEivizjRtp

Step 1. Determine the available drive bays based on the drive bay labels applied. The following labels

indicate that the drive bays support both NVMe and SATA/SAS drives. Otherwise, only SATA/SAS
drives are supported.

Figure 67. Drive bay labels of both NVMe and SATA/SAS drives

Table 79. Drive bay labels of both NVMe and SATA/SAS drives

Drive bay 4-7 label of both NVMe and SATA/SAS

drives

Drive bay 12-15 label of both NVMe and SATA/

SAS drives

Notes:

1. Make sure to install the correct type of drives into supported by corresponding drive bays.

Drive type information is available on the drive.

Step 2.  Remove the drive bay filler if it has been installed in the drive bay.
Step 3.  Gently rotate the release latch away to unlock the drive handle.
Step 4.  Slide the drive into the drive bay, and push it until it stops.

108

ThinkSystem SR860 Setup Guide

Summary of Contents for 7X69













































































































































































Search results

Summary of Contents for 7X69

Reviews:

Related manuals for 7X69

Brands by name

Popular brands

Lenovo 7X69, Setup Manual

Search results

Summary of Contents for 7X69

Reviews:

Related manuals for 7X69

Brands by name

Popular brands