manualshive.com logo in svg

Lenovo 7X69, Setup Manual

Share
Download
Lenovo 7X69 Setup Manual Download Page 44

Four processors installed

Figure 30. Cable routing, AnyBay backplane

Note:

Install the processor and memory expansion tray before connecting the signal cables to NVMe 

connector on the expansion tray.

Table 24.  Cables and adapters for routing

1 

SATA/SAS RAID adapter (8i)

3 

Direct NVMe signal cables for processor and memory 

expansion tray

2 

NVMe connectors on the processor and memory 

expansion tray

4 

SATA/SAS signal cables (720 mm)

Cable routing for 2.5-inch drives to two backplanes

Use this section to understand how to route cables for 2.5-inch drives to two backplanes.

Following is the list of combinations of cable routing for 2.5-inch drives to two backplanes.

• 

“Connecting signal cables to two backplanes” on page 38

– 

“8-bay bac 8-bay backplane” on page 38

– 

“AnyBay bac 8-bay backplane ” on page 40

– 

Two processors installed

36

ThinkSystem SR860 Setup Guide

Summary of Contents for 7X69













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands