Lektri-Co SVIK User And Installation Manual Download Page 3

Page: 3 / 36

COPYRIGHT

trademark of SC CIVITRONIC SRL.
SVIK™ is a product designed and manufactured by LEKTRI.CO.

This document is copyright protected. Copying, reproduction or

translation of this document or sections from this document, without

prior written consent from LEKTRI.CO is strictly prohibited and is unlawful.

The information described in this document including any attachments

is confidential and is intended only for the SVIK users, therefore any

disclosure or distribution (in any format) is strictly prohibited and is

unlawful.

Any software applications or web portals that are needed to operate the

SVIK charger are subject to license agreements and can only be used in

accordance with the terms and conditions of that specific agreement.

DISCLAIMER

The information presented in this document can be changed without

prior notice and does not represent any commitment on the part of

LEKTRI.CO.

LEKTRI.CO is not liable to any person or business for any direct or indirect

potential injuries, damages or losses caused by the improper installation

or use of the SVIK charger.

Installation of the SVIK charger must always be performed by certified

personnel in electrical installations and accordance with the local

electrical regulations.

Summary of Contents for SVIK





































Search results

Summary of Contents for SVIK

Reviews:

Related manuals for SVIK

Brands by name

Popular brands

Lektri-Co SVIK, User And Installation Manual

Search results

Summary of Contents for SVIK

Reviews:

Related manuals for SVIK

Brands by name

Popular brands