Lektri-Co SVIK User And Installation Manual Download Page 10 | Manualshive

Page: 10 / 36

background image

SVIK user and installation manual

10

GREEN

fading in and out: available and connected to

Wi-Fi.

GREEN

continuously lit: available and unused (not

connected to the electric vehicle).

BLUE

continuously lit: connected to the electric vehicle

and waiting for the car to start the charging process.

PURPLE

continuously lit: connected to the electric

vehicle and waiting for the remote server to authorize

the start of the charging process.

WHITE

, each

segment is lit in a clockwise rotating

pattern: connected to the electric vehicle and charging.

RED continuously lit: error - general fault, charging

not possible please see the Troubleshooting section or

contact the manufacturer (for contact details see 8.2

Support section).

YELLOW

continuously lit: the charger is performing a

firmware update.

SVIK CHARGER’S LED

Different charger statuses are represented by different LED colours as

described below:

«
...
8
9
10
11
12
...
»

Summary of Contents for SVIK





































Reviews:

No comments

Related manuals for SVIK

A La Cart BLT-27698

Brand: Mooreco Pages: 8

Brand: Mec Pages: 4

Brand: Kodak Pages: 24

Brand: Facom Pages: 23

Monogram MHCH3V

Brand: Ericsson GE Pages: 12

Brand: SpectraLink Pages: 2

Brand: Wentronic Pages: 8

Brand: Gacell Pages: 16

Brand: Velleman Pages: 3

Brand: OLIMEX Pages: 14

Brand: Motorola Pages: 28

Brand: Hoberg Pages: 60

Brand: Sony Pages: 1

InfoLITHIUM NP-QM91D

Brand: Sony Pages: 2

InfoLITHIUM NP-QM71D

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands