manualshive.com logo in svg

Learjet 20 Series, Pilot Training Manual

The GE 20 Series offers an exceptional range of home appliances designed to simplify your everyday tasks. With the Owner's Manual and Installation Instructions readily available, you can easily access and download the user manual for free from our website, ensuring a seamless experience with your new GE appliance.

Share
Download
background image

Engine bleed air is used to heat the windshields,
wing leading edges, and the engine front frame.

An alcohol system is installed for radome anti-
icing and as a backup to the pilot’s windshield
bleed-air anti-icing.

NOTE

All anti-ice systems except engine
front frame heat require electrical
power for operation.

All anti-icing equipment must be turned on 
before icing conditions are encountered. To
delay until ice buildup is visually detected on
aircraft surfaces constitutes an unacceptable
hazard to safety of flight.

Icing conditions exist when visible moisture
is present and the indicated ram-air tempera-
ture (RAT) is +10º C or below. Takeoff into
icing conditions is permitted with all bleed-
air anti-icing systems on. The RAT gage should
be checked frequently when flying in or en-
tering areas of visible moisture.

During descents, the cabin altitude may in-
crease unless sufficient engine rpm is main-
t a i n e d   t o   c o m p e n s a t e   f o r   t h e   a d d i t i o n a l
bleed-air use. To ensure adequate bleed air
for anti-ice protection and cabin pressuriza-
tion, maintain at least 80% engine rpm.

Figure 10-1 illustrates the ice-protected areas.

10-2

FOR TRAINING PURPOSES ONLY

LEARJET 20 SERIES  PILOT TRAINING MANUAL

FlightSafety

international

HORIZONTAL STABILIZER

LEADING-EDGE ANTI-ICE

(ELECTRIC)

FRONT FRAME

ANTI-ICING

(BLEED AIR)

WING LEADING EDGE

ANTI-ICE (BLEED AIR)

WINDSHIELD HEAT
(BLEED AIR AND ALCOHOL)

NACELLE LIP ANTI-ICE
(ELECTRIC)

RADOME ANTI-ICE
(ALCOHOL)

Figure 10-1.

Ice and Rain Protected Areas

Summary of Contents for 20 Series






















































































































































































































































































































































































Reviews:

No comments

Related manuals for 20 Series

A-I-R ATOS Series Operation Manual preview
ATOS Series
Brand: A-I-R Pages: 20
Beechcraft Duke 60 Series Maintenance Manual preview
Duke 60 Series
Brand: Beechcraft Pages: 28
Cabrinha Prodigy Assembly Assistance preview
Prodigy
Brand: Cabrinha Pages: 3
ICARO paragliders XEMA light Manual preview
XEMA light
Brand: ICARO paragliders Pages: 18
Ozone Angel v1 Pilot'S Manual preview
Angel v1
Brand: Ozone Pages: 23
MAC PARA PASHA II User Manual preview
PASHA II
Brand: MAC PARA Pages: 10
AirBorne WindSports Edge XT 582-L Cruze Operating Instructions Manual preview
Edge XT 582-L Cruze
Brand: AirBorne WindSports Pages: 110
Roko Aero NG 4 ML Operating Instructions Manual preview
NG 4 ML
Brand: Roko Aero Pages: 69
Flow Paragliders freedom2 L User Manual preview
freedom2 L
Brand: Flow Paragliders Pages: 30
Flow Paragliders Cosmos Power Series Manual preview
Cosmos Power Series
Brand: Flow Paragliders Pages: 35
Community Playthings J900 Product Manual preview
J900
Brand: Community Playthings Pages: 2
Air Creation BioniX 15 Pilot Operating Handbook preview
BioniX 15
Brand: Air Creation Pages: 22

Brands by name

Popular brands

Load more brands