Learjet 20 Series Pilot Training Manual Download Page 173 | Manualshive

Page: 173 / 373

background image

normal position. The loss of either electrical
power or servo air automatically positions the
valve to the emergency position. Below are
situations where this occurs:

A. Both engines shut down (loss of servo

pressure).

B. Cabin altitude is 9,500 feet (aneroid switch

opens circuit to the solenoid valve)

C. AIR BLEED switch to EMER (opens

circuit to the solenoid valve)

D. Complete DC power failure (no power

available to solenoid valve)

E. Servo regulator failure (no servo

pressure available)

Bleed-Air Check Valves (6)

Three bleed-air check valves (Figure 9-2) are
installed in the bleed-air ducting from
each engine. Each check valve allows airflow in
one direction and blocks airflow in the opposite
direction. These check valves prevent loss of
bleed air during single-engine operation or
actuation of the emergency pressurization valves.

Bleed-Air Manifold

The bleed-air manifold serves as a collection
point for engine bleed air from either or both
engines. From the manifold, bleed air is
distributed to the flow control valve for cabin
pressurization and heating, windshield anti-ice
(defog) valve, wing anti-ice, and the hydraulic
reservoir pressure regulator.

Flow Control Valve

The flow control valve regulates the flow of
bleed air to the cabin for normal pressurization
and heating. It is controlled by a two-position
CAB AIR switch on the pressurization module.
The OFF position closes the valve completely.
The ON position allows sense line pressure from
the venturi (located downstream) to modulate
the flow control valve to maintain a constant
airflow to the cabin. With loss of DC electrical
power, the valve fails to the normal ON position.

Cabin-Air Warning Lights

The red L and R CAB AIR warning lights on the
glareshield annunciator panel illuminate when
an associated duct temperature sensor detects
excessive temperatures.

Servo Air Manifold

Bleed air is tapped prior to the bleed-air shutoff
valves and is routed through a check valve to the
servo air manifold (Figure 9-2). From this
manifold, air is ducted directly to the alcohol anti-
icing system and through two regulators. The air
from one regulator is used for cabin temperature
control. Air from the other regulator supplies
servo air pressure to operate the flow control
valve, emergency pressurization valves, and the
pressurization vacuum regulator (jet pump). See
Figure 9-3 for AIR BLEED switch locations.

9-5

FOR TRAINING PURPOSES ONLY

LEARJET 20 SERIES PILOT TRAINING MANUAL

FlightSafety

international

CABIN AIR FLOW

INSTRUMENT PANEL

LOCATOR

AIR BLEED

EMER

ON

OFF

ON

OFF

CAB

AIR

MAX

NORM

OFF

23-003 THROUGH 24-229
25-003 THROUGH 25-064

24-230 THROUGH 24-349
25-070 THROUGH 25-226

24-350 AND SUBSEQUENT
25-227 AND SUBSEQUENT

NORM

MAX

ON

OFF

A

I

R

B

L

E
E
D

AIR

BLEED

Figure 9-3.

AIR BLEED Switches

«
...
171
172
173
174
175
...
»

Summary of Contents for 20 Series






















































































































































































































































































































































































Reviews:

No comments

Related manuals for 20 Series

Brand: Prism Designs Pages: 6

Cessna 680-0001

Brand: Textron Pages: 24

Brand: Cessna Pages: 192

Brand: U-Turn Pages: 30

Brand: Desert Aircraft Pages: 10

Brand: SKY PARAGLIDERS Pages: 35

Brand: SKY PARAGLIDERS Pages: 40

Brand: DaVinci Pages: 24

Brand: Parajet Pages: 8

EV-97? EUROSTAR ?model 2000 version R

Brand: EVEKTOR-AEROTECHNIK Pages: 82

Brand: Dudek Pages: 28

Brand: Dudek Pages: 32

Brand: Dudek Pages: 48

Brand: Ecotop Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands