manualshive.com logo in svg

Learjet 20 Series, Pilot Training Manual

The GE 20 Series offers an exceptional range of home appliances designed to simplify your everyday tasks. With the Owner's Manual and Installation Instructions readily available, you can easily access and download the user manual for free from our website, ensuring a seamless experience with your new GE appliance.

Share
Download
background image

ICE DETECTION

During daylight operation, ice accumulation
can be visually detected on the windshield, the
wing leading edges, and tip tanks.

WINDSHIELD ICE DETECTION

During night operations, the windshield ice
detection lights indicate ice or moisture for-
mation on the windshield. Two probes, one on
the pilot’s side of the glareshield and one on the
copilot’s side, contain red lights which con-
tinuously shine on the inside of the windshield
surface (Figure 10-2). The ice detection lights
normally shine through unseen. They reflect red
spots approximately 1 1/2 inches in diameter
if ice or moisture has formed on the windshield.

The ice detection light on the pilot’s side is in-
side the anti-ice airstream; the light on the
copilot’s side is located outside the anti-ice
airstream. For this reason, the copilot’s light
should be monitored whenever windshield
heat or the alcohol anti-ice system is in oper-
ation. The ice detection lights are illuminated
whenever airplane electrical power is on. The
lights use DC power routed through the L and
R ICE DET circuit breakers located on the
pilot’s/copilot’s or baggage compartment 
circuit-breaker panels.

WING ICE DETECTION

During darkness, the recognition light (Figure
10-3) can be used to confirm ice buildup on the
right tip tank. Some airplanes are equipped with
a second recognition light in the left tip tank.

The optional wing ice inspection/egress light,
installed on the right side of the fuselage, 
allows ice buildup to be detected on the wing
inboard leading edge.

ANTI-ICE SYSTEMS

ENGINE ANTI-ICE SYSTEM
(NACELLE HEAT)

The engine anti-ice system (Figure 10-4) pro-
vides anti-ice protection for the engine na-
celle inlet lips and the inlet guide vanes and
nose cone. The nacelle lips are heated elec-
trically and the front frame pneumatically.

10-3

FOR TRAINING PURPOSES ONLY

LEARJET 20 SERIES  PILOT TRAINING MANUAL

FlightSafety

international

Figure 10-3.

Recognition Light

WINDSHIELD

(REF)

ICE DETECTOR

ASSEMBLY

FORWARD
GLARESHIELD

UP

FWD

Figure 10-2.

Ice Detection Lights

Summary of Contents for 20 Series






















































































































































































































































































































































































Reviews:

No comments

Related manuals for 20 Series

Cessna 177RG0073 Owner'S Manual preview
177RG0073
Brand: Cessna Pages: 85
Cessna 172 0970 Owner'S Manual preview
172 0970
Brand: Cessna Pages: 78
Hacker Para-RC Bullix XXL Manual preview
Para-RC Bullix XXL
Brand: Hacker Pages: 10
MAC PARA Aegis 33 Folding Instructions And Manual preview
Aegis 33
Brand: MAC PARA Pages: 8
Cabrinha 2018 DOUBLE AGENT User Manual preview
2018 DOUBLE AGENT
Brand: Cabrinha Pages: 10
Ocean Rodeo Stick-Shift Manual preview
Stick-Shift
Brand: Ocean Rodeo Pages: 15
Gin Boomerang RF M User Manual preview
Boomerang RF M
Brand: Gin Pages: 23
GRAVITY X maniac Manual preview
X maniac
Brand: GRAVITY Pages: 36
Beechcraft Bonanza 36 Pilot Operating Handbook preview
Bonanza 36
Brand: Beechcraft Pages: 356
U-Turn Alpine Peak 2 XS Manual preview
Alpine Peak 2 XS
Brand: U-Turn Pages: 25
Zodiac Aerospace ATOM Legend S T1 Use And Maitain Manual preview
ATOM Legend S T1
Brand: Zodiac Aerospace Pages: 83
Vulcanair V1 series Service Bulletin preview
V1 series
Brand: Vulcanair Pages: 19
Piper PA-32R-301T SARATOGA S Maintenance Manual preview
PA-32R-301T SARATOGA S
Brand: Piper Pages: 956

Brands by name

Popular brands

Load more brands