manualshive.com logo in svg

Leadshine ES-DH Series, Hardware Manual

The Leadshine ES-DH Series is a highly efficient and reliable product, designed to optimize performance in various applications. To ensure hassle-free usage, we provide a comprehensive Hardware Manual for free download at manualshive.com, offering step-by-step instructions and valuable insights. Enhance your experience with this exceptional device today!

Share
Download
background image

 

iii 

Table of Contents 

Introduction to Easy Servo

.............................................................................................................................................. 1 

Getting Start

................................................................................................................................................................... 1 

Wiring Diagrams

..................................................................................................................................................... 2 

Connecting Power Supply

....................................................................................................................................... 3 

ES-DH1208

....................................................................................................................................................... 3 

ES-DH2306

....................................................................................................................................................... 3 

Connecting Motor

................................................................................................................................................... 4 

ES-DH1208 and the ES-MH2 Series Motor

...................................................................................................... 4 

ES-DH2306 and the ES-MH3 Series Motor

...................................................................................................... 4 

Connecting Encoder

................................................................................................................................................ 5 

Connecting Control Signal

...................................................................................................................................... 6 

Pulse, Direction, Enable Input

........................................................................................................................ 6 

Alarm Output

.................................................................................................................................................. 7 

Connecting PC

......................................................................................................................................................... 8 

Typical Connections

........................................................................................................................................................ 9 

Wiring Notes

................................................................................................................................................................. 10 

Configuration

................................................................................................................................................................ 10 

Configuring an ES drive by the on-board HMI

......................................................................................................11 

Display Data Mode

....................................................................................................................................... 12 

Edit Parameter Mode

.................................................................................................................................... 13 

Configuration Example via the on-board HMI

............................................................................................. 15 

Calculating Rotation Speed and Angle

................................................................................................................. 16 

Rotating the Motor via the On-board HMI

.......................................................................................................... 16 

Rotating the Motor by Motion Controller

............................................................................................................ 17 

Rotating the ES Motor in PC Software

................................................................................................................. 17 

Power Supply Selection

................................................................................................................................................. 18 

Multiple Drives

...................................................................................................................................................... 18 

Selecting Supply Voltage

...................................................................................................................................... 18 

Recommended Supply Voltage

............................................................................................................................. 19 

Control Signal Setup Timing

......................................................................................................................................... 19 

Current Control Detail

................................................................................................................................................... 20 

Fine Tuning

.................................................................................................................................................................... 20 

Protection Functions

..................................................................................................................................................... 20 

Over-current Protection

........................................................................................................................................ 21 

Over-voltage Protection

....................................................................................................................................... 21 

Position Following Error Protection

..................................................................................................................... 21 

Frequently Asked Questions

......................................................................................................................................... 22 

Problem Symptoms and Possible Causes

............................................................................................................. 22 

Warranty

....................................................................................................................................................................... 23 

Exclusions

.............................................................................................................................................................. 23 

Summary of Contents for ES-DH Series





























Reviews:

No comments

Related manuals for ES-DH Series

INVT MH860 Series Operation Manual preview
MH860 Series
Brand: INVT Pages: 125
Danfoss ADAP-KOOL AKD 102 Operating Instructions Manual preview
ADAP-KOOL AKD 102
Brand: Danfoss Pages: 130
National Instruments NI 9505E Operating Instructions And Specifications preview
NI 9505E
Brand: National Instruments Pages: 35
YASKAWA CIMR-E7 series Technical Manual preview
CIMR-E7 series
Brand: YASKAWA Pages: 47
Beckhoff EL7201-0010 Documentation preview
EL7201-0010
Brand: Beckhoff Pages: 208
UNI Geräte MG A C Series Manual preview
MG A C Series
Brand: UNI Geräte Pages: 14
Label Vista SMP Installation Manual preview
Vista SMP
Brand: Label Pages: 56
Simu T3.5 AC Original Instructions preview
T3.5 AC
Brand: Simu Pages: 2
VLT AQUA Drive FC 200 Instruction Manual preview
AQUA Drive FC 200
Brand: VLT Pages: 96
LinMot E1450-EC-QN-0S Installation Manual preview
E1450-EC-QN-0S
Brand: LinMot Pages: 23
Eurotherm Drives 584 Series Product Manual preview
584 Series
Brand: Eurotherm Drives Pages: 71
Dakota Digital ECD-200BT-1 Quick Start Manual preview
ECD-200BT-1
Brand: Dakota Digital Pages: 10
Unitek TVD3.2 bl Series Manual preview
TVD3.2 bl Series
Brand: Unitek Pages: 40
Eaton PowerXL DA1 Installation Manual preview
PowerXL DA1
Brand: Eaton Pages: 203
Idex ISM 1143 Operating Manual preview
ISM 1143
Brand: Idex Pages: 52
Idex ISMATEC ISM 915 Operating Manual preview
ISMATEC ISM 915
Brand: Idex Pages: 56
Danfoss 73691290 Operating Manual preview
73691290
Brand: Danfoss Pages: 20
G-U ELTRAL S 230 Installation, Operation And Maintenance Instructions preview
ELTRAL S 230
Brand: G-U Pages: 20

Brands by name

Popular brands

Load more brands