background image

LAUNCH                                                               KWA-300 3D Wheel Aligner 

iv 

Working on the electrical equipment: 

 

 

Repairs on electrical equipment of the 

machine may only be performed by trained electricians! 
Electrical equipment must be routinely inspected! 
Re-attach any loose connections! 
Immediately replace damaged lines/cables! 

Always keep housings of electrical equipment closed! 
Access is only permitted for authorized personnel with 
key/tools! 
Never spray the housing of electrical equipment with a 
hose when cleaning! 

 

Observe environmental regulations: 

 

The legal regulations for waste prevention and 

proper recycling/disposal must be adhered to for all 
operations on and with the machine. 
Especially during installation, repair and maintenance 

operations, water-polluting materials, such as: 
Lubricants and oils - hydraulic oils - coolants. 
 
Solvent-containing cleaning liquids may not pollute the 
ground or reach the sewage system!! 

These materials must be stored, transported, collected 
and disposed of in suitable containers! 
 

Summary of Contents for KWA-300



































Reviews: