background image

LAUNCH                             KWA-300 3D Wheel Aligner                Operation Instructions

 

4-6 

[Figure format]: Figure format data display mode is 

newly added in the system. Click [System Setting] and 
select [Switch between Letter Format and Figure 
Format]. The interface is as shown in Fig.4.18.   

 

Fig.4.18 

 

Caution: 
1.

 

Before perform kingpin measurement, please 

install brake pedal depressor and lock the 
hand brake first, in order to ensure the 
vehicle wheels cannot move; remove the 
steering wheel holder finally. 

2.

 

The measured values are displayed with 

different colors on each measurement 
interface. 

z

 

Green, it indicates that the measured 
values are within the standard 
specifications. 

z

 

Red, it indicates that the measured 
values are beyond the standard 
specifications. 

z

 

Blue, it indicates that this measured 
parameter has not the standard 

specification. 

 

Rear axle measurement 

This interface can provide the real-time result related to 
rear axle measurement, the operator can compare the 
measurement result with the reference data while 
adjusting the vehicle, until the vehicle is adjusted to the 

best status. The interface is as shown in Fig.4.19. 

 
 

 

 
 
 

Fig.4.19 

 

[Double click]: Double click (with left key of the mouse) 
on the data display forms for camber and toe-in of RL 
and RR wheels, the corresponding displayed data will 
be enlarged. The interface is as shown in Fig.4.20. 

 

Fig.4.20 

 
[Additional Measurement]: This interface provides an 
operating platform for special measurement, which can 
measure and display left lateral offset, right lateral offset, 
axle offset, front setback, rear setback, track width 

difference and wheelbase difference, etc. The interface 
is as shown in Fig.4.21. 

 

Fig.4.21

 

 

Double click 

Put up the vehicle body 

Summary of Contents for KWA-300



































Reviews: