background image

LAUNCH                                                                 KWA-300 3D Wheel Aligner

 

 

Warranty 

 

THIS WARRANTY IS EXPRESSLY LIMITED TO 
PERSONS WHO PURCHASE LAUNCH PRODUCTS 
FOR PURPOSES OF RESALE OR USE IN THE 
ORDINARY COURSE OF THE BUYER’S BUSINESS.   
LAUNCH electronic product is warranted against defects 

in materials and workmanship for 1 year from date of 
delivery to the user. This warranty does not cover any 
part that has been abused, altered, used for a purpose 
other than for which it was intended, or used in a 
manner inconsistent with instructions regarding use. The 

exclusive remedy for any automotive meter found to be 
defective is repair or replacement, and LAUNCH shall 
not be liable for any consequential or incidental 
damages. Final determination of defects shall be made 
by LAUNCH in accordance with procedures established 
by LAUNCH. No agent, employee, or representative of 

LAUNCH has any authority to bind LAUNCH to any 
affirmation, representation, or warranty concerning 
LAUNCH automotive meters, except as stated herein.   

Disclaimer 

 

THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER 

WARRANTY, EXPRESSED OR IMPLIED, INCLUDING 
ANY WARRANTY OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE.   

Order Information 

 

Replaceable and optional parts can be ordered directly 

from your LAUNCH authorized tool supplier. Your order 
should include the following information: 
1.

 

Quantity 

2.

 

Part number 

3.

 

Item description 

Customer Service 

 

If you have any questions on the operation of the unit, 
please call: 86-755-84528288, or fax: 86-755-84528872. 
 
If your unit requires repair service, return it to the 

manufacturer with a copy of the sales receipt and a note 
describing the problem. If the unit is determined to be in 
warranty, it will be repaired or replaced at no charge. If 
the unit is determined to be out of warranty, it will be 
repaired for a nominal service charge plus return freight. 

Send the unit pre-paid to: 
 
Attn: Customer Service Center 
Shenzhen Launch Tech. Co., Ltd. 
LAUNCH Industrial Park,   

North of Wuhe Rd., 

Banxuegang,  

Longgang, 
Shenzhen, Guangdong, 
P. R. China   

 

 
 
 
 

 

Summary of Contents for KWA-300



































Reviews:

Related manuals for KWA-300