Land Pride HRS3025 Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 44

background image

Table of Contents

1/16/20

©

Copyright 2020 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 8
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Number  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Further Assistance   . . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 1: Assembly & Set-up . . . . . . . . . . . . 9

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . . 9
Dealer Preparations   . . . . . . . . . . . . . . . . . . . . . . . . 9
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 9
Uncrating   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pump & Gearbox Assembly   . . . . . . . . . . . . . . . . . 10

No Valve No Cooler Option . . . . . . . . . . . . . . . . 11

Oil Cooler  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
No Valve With Cooler Option   . . . . . . . . . . . . . . . . 13
Manual Valve With Oil Cooler Option   . . . . . . . . . . 14
Solenoid Valve W/ Oil Cooler Option   . . . . . . . . . . 14

Section 2: Hook-up to Reservoir . . . . . . . . . 16

Driveline Installation  . . . . . . . . . . . . . . . . . . . . . . . 16
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . 16
3-Point Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Driveline Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . 17

Check Driveline Collapsible Length  . . . . . . . . . . 18
Check Driveline Maximum Length  . . . . . . . . . . . 18
Check Driveline Interference  . . . . . . . . . . . . . . . 19

Hydraulic Hose Assembly . . . . . . . . . . . . . . . . . . . 20

Large Face Coupler Option . . . . . . . . . . . . . . . . 20
Small face Coupler Option . . . . . . . . . . . . . . . . . 20

Hook-up Hoses to The Reservoir . . . . . . . . . . . . . 20

No Valve No Oil Cooler Option   . . . . . . . . . . . . . 20
No Valve With Oil Cooler Option   . . . . . . . . . . . . 20
Manual Valve & Solenoid Valve Options   . . . . . . 20

Hook-up Hoses to The Attachment  . . . . . . . . . . . . 20
Case Drain Option   . . . . . . . . . . . . . . . . . . . . . . . . 21
Fill Hydraulic Reservoir  . . . . . . . . . . . . . . . . . . . . . 22
Control Box Hook-up . . . . . . . . . . . . . . . . . . . . . . . 22

Section 3: Optional Equipment . . . . . . . . . . . 24

Valve Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

No Valve No Cooler Option   . . . . . . . . . . . . . . . . 24
No Valve With Cooler Option  . . . . . . . . . . . . . . . 24
Manual Valve Option With Cooler   . . . . . . . . . . . 25
Solenoid Valve Option W/ Cooler  . . . . . . . . . . . . 25
Small Flat Face Couplers  . . . . . . . . . . . . . . . . . . 26
Large Flat Face Couplers . . . . . . . . . . . . . . . . . . 26
Case Drain Kit With Coupler   . . . . . . . . . . . . . . . 26

Slow Moving Vehicle Sign (Accessory) . . . . . . . . . 26

Section 4: Adjustments . . . . . . . . . . . . . . . . . 27

Park Stands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Leveling Adjustments . . . . . . . . . . . . . . . . . . . . . . 27

Section 5: Operating Procedures . . . . . . . . . 28

Startup Checklist  . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Operating Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General Operating Instructions  . . . . . . . . . . . . . . . 29
Unhook Hydraulic Reservoir  . . . . . . . . . . . . . . . . . 30

Section 6: Maintenance & Lubrication . . . . . 31

Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . 31

Check Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . 31
Replace Filter Element  . . . . . . . . . . . . . . . . . . . . 32
Change Hydraulic Fluid   . . . . . . . . . . . . . . . . . . . 32
Hydraulic Pump  . . . . . . . . . . . . . . . . . . . . . . . . . 32

Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 33
Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . 34

Driveline Shaft U-Joints  . . . . . . . . . . . . . . . . . . . 34
Inner Tube Bearings . . . . . . . . . . . . . . . . . . . . . . 34
Driveline Profiles   . . . . . . . . . . . . . . . . . . . . . . . . 34
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Section 7: Specifications & Capacities  . . . . . 35
Section 8: Features & Benefits   . . . . . . . . . . . 36
Section 9: Troubleshooting  . . . . . . . . . . . . . . 37
Section 10: Torque Values Chart . . . . . . . . . . 38
Section 11: Warranty   . . . . . . . . . . . . . . . . . . . 39

«
1
2
3
4
5
...
»

Summary of Contents for HRS3025













































Reviews:

No comments

Related manuals for HRS3025

Brand: NORLUX Pages: 2

Brand: Labnet Pages: 5

Brand: Hanil Pages: 60

Brand: Parata Pages: 40

Brand: Facsimile Pages: 16

Brand: QBC Diagnostics Pages: 65

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: Dana Design Pages: 20

Brand: Pani Pages: 12

Brand: FASTER TOOLS Pages: 19

McDonnell & Miller PSE-800-M

Brand: Xylem Pages: 20

Brand: Aspect Medical Systems Pages: 104

Brand: Hupfer Pages: 153

ResQCRP ResQPUMP ACD-CPR

Brand: Advanced Circulatory Pages: 2

Big Wheel RN1 Series

Brand: Osborne Pages: 8

Brand: Biosonic Pages: 2

Brand: Petzl Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands