Section 2: Hook-up to Reservoir
HRS3025 Hydraulic Reservoir System 316-271M
1/16/20
16
Hydraulic Reservoir 3-Point Hitch
Figure 2-1
Driveline Installation
Refer to Figure 2-1:
The driveline is coupled to the tractor power take-off shaft
and reservoir gearbox shaft with pull collars:
1. Align yoke splines on the inner driveline with gearbox
shaft splines.
2. Pull back on the pull collar and push yoke partway
onto the gearbox input shaft.
3. Release pull collar and continue to push driveline
yoke forward until pull collar locks in place.
4. Move driveline yoke back and forth several times to
make sure pull collar has locked in place and cannot
slip off the shaft.
Tractor Shutdown Procedure
The following are basic tractor shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your tractor’s Operator’s Manual
before leaving the operator’s seat.
1. Reduce engine speed and disengage power take-off
if engaged.
2. Park tractor and reservoir on level, solid ground.
3. Operate 3-point control lever to fully lower the
Hydraulic Reservoir.
4. Lower front loader arms fully down.
5. Put tractor in park or set park brake, turn off engine,
and remove switch key to prevent unauthorized
starting.
6. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
7.
Wait for all components to come to a complete stop
before leaving the operator’s seat.
Gearbox Input Shaft
Outer Driveline
35634
Inner Driveline
Pull Collar
Pull Collar
IMPORTANT:
The driveline must be lubricated
before putting it into service. Refer to
8. Use steps, grab-handles and anti-slip surfaces when
stepping on and off the tractor.
3-Point Hook-Up
Refer to Figure 2-2 on page 17:
DANGER
!
To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the
implement. Keep people and animals away while backing-up
to the implement or pulling away from the implement. Do not
operate hydraulic controls while a person or animal is directly
behind the power machine or near the implement.
WARNING
!
To avoid serious injury or death:
Lightweight tractors with rear attached implements may need
weights added to the front to maintain steering control.
Consult your tractor Operator’s Manual to determine proper
weight requirements and maximum weight limitations.
A 3-point Category I or Category II hitch is required. The
lower 3-point arms of the 3-point hitch must be stabilized
to prevent side-to-side movement. Most tractors have
sway blocks or adjustable chains for this purpose.
A 3-point Category I or Category II hitch is required. The
lower 3-point arms of the 3-point hitch must be stabilized
to prevent side-to-side movement. Most tractors have
sway blocks or adjustable chains for this purpose.
1. Slowly back tractor to the Hydraulic Reservoir while
using tractor’s 3-point hydraulic controls to align
lower lift arm hitch holes with reservoir clevis lug
holes.
2. Shut tractor down before dismounting. Refer to
3. With tractor’s lower hitch arms aligned and
positioned in the clevises, insert lower 3-point hitch
pins through clevis lugs and lower arm holes. Secure
hitch pins with linchpins.
4. Connect top center link to top center clevis lugs using
clevis pin and hairpin cotter.
5. Ensure that the lower hitch arms are blocked to
prevent excessive side movement.
6. Using tractor’s 3-point lift, raise reservoir up until
park stands are 1" or 2" off the ground.
7.
Remove wire retaining pins and raise park stands
fully up. Re-insert wire retaining pins and secure by
making sure wire retainers are caught over the pins.
NOTE:
Land Pride’s Quick Hitch can be attached to
the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride
dealer to purchase a Quick-Hitch.
Section 2: Hook-up to Reservoir
