Land Pride HRS3025 Operator'S Manual Download Page 38

Page: 38 / 44

Section 6: Maintenance & Lubrication

HRS3025 Hydraulic Reservoir System 316-271M

1/16/20

Table of Contents

24871

24873

30861

“DO NOT OVERFILL!” When checking oil, gearbox

should be oriented with flat side down as shown.

Unbolt speed pump mount from reservoir frame

and rotate gearbox down to check oil level.

Lubrication Points

Hours

Driveline Shaft U-Joints

Type of lubrication: Multi-purpose grease
Quantity - 4 to 8 Pumps

Hours

Inner Tube Bearings

Type of lubrication: Multi-purpose grease
Quantity - As Required

Hours

Driveline Profiles

Type of lubrication: Multi-purpose grease
Quantity - Clean & coat inner profile tube of driveline with

a light film of grease and then reassemble.

Gearbox

If oil is below bottom of site gauge/plug hole (See arrow),

remove site gauge/oil plug and add recommended gear

lube through plug hole until oil flows out of plug hole.

Reinstall and tighten site/gauge/oil plug.
Type of lubrication: 80-90W EP gear lube
Quantity = Fill until oil begins to flow out of plug hole.

NOTE:

Check oil if gearbox is leaking. Do not overfill!

Gearbox should be oriented as shown when checking

oil. Always check oil level when gearbox is cold.

Needed

Hrs

Multi-purpose

spray lube

Multi-purpose

grease lube

Multi-purpose

oil lube

Intervals in hours at which

lubrication is required

Lubrication

Legend

Summary of Contents for HRS3025













































Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands

Land Pride HRS3025, Operator'S Manual

Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands