Land Pride HRS3025 Operator'S Manual Download Page 14

Page: 14 / 44

Section 1: Assembly & Set-up

HRS3025 Hydraulic Reservoir System 316-271M

1/16/20

Table of Contents

Pump & Gearbox Assembly

Refer to Figure 1-3:

The pump, capable of 25 gpm @ 540 rpm, is

mounted under the reservoir tank and connected

to tractor power take-off shaft with a driveline.
1. Separate pump rear guard (#3) from high

speed pump mount (#2).

2. Verify gearbox (#12) is full of oil.

a. Rotate high speed pump mount (#2) onto

its right side plate “D”.

b. View sight glass in gearbox (#12). Oil

should be visible in sight glass. Some

tipping of unit and a flashlight may be

needed to see oil line.

c. If low or out of oil, remove sight glass and

add recommended gearbox oil provided

under

“Lubrication Points”

on page 34.

3. Screw 1 5/16" MJIC x 1 5/16" MORB

elbow (#17) to “OUT” port of hydraulic

pump (#11) until snug.

4. Screw 1 5/8" MORB x 1 1/4" HB elbow (#15)

to the “IN” port of hydraulic pump (#10) until

tight.

5. Center hydraulic hose (#1) in slot “D” and

screw hydraulic hose to elbow (#17) as

follows:

•

No valve Option:

Screw 1" x 40" long

hydraulic hose (#1) to elbow (#17) until
tight.

•

Manual & Solenoid Valve Option:

Screw

1" x 34" long hydraulic hose (#1) to
elbow (#17) until tight.

6. With hydraulic hose (#1) centered in slot “D”,

tighten elbow (#17) to hydraulic pump (#11).

Attach high speed pump mount (#2) to

reservoir tank with 1/2"-13 x 1 1/2" GR5 cap

screws (#6), spring lock washers (#10), and

hex nuts (#8). Tighten nuts to the correct

torque.

8. Remove cap from nipple “B” and apply teflon

tape to nipple. Screw ball valve (#13) to pipe

nipple “B” until tight with control lever on top.

9. Apply teflon tape to elbow (#14) and screw

elbow onto ball valve (#13) until tight with

elbow turned down as shown.

10. Attach suction hose (#16) to elbow (#15) with

worm drive clamp (#4) and tighten.

11. Attach suction hose (#16) to elbow (#14) with

worm drive clamp (#4). Make sure suction

hose passes through slot “C” and tighten

worm drive clamp (#4).

12. Tighten elbow (#15) to hydraulic pump (#11).

Pump & Gearbox Assembly

Figure 1-3

13. Attach pump rear guard (#3) to high speed pump mount (#2)

with 3/8"-16 x 1 1/4" GR5 hex head cap screws (#5), spring

lock washers (#9), and nuts (#7). Tighten nuts to the correct

torque.

30394

Summary of Contents for HRS3025













































Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands

Land Pride HRS3025, Operator'S Manual

Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands