Land Pride HRS3025 Operator'S Manual Download Page 29

Page: 29 / 44

Section 3: Optional Equipment

HRS3025 Hydraulic Reservoir System 316-271M

1/16/20

Table of Contents

Manual Valve Option With Cooler

316-282A

Manual Valve Option With Cooler

Refer to Figure 3-3:

The manual valve is equipped with a spring return lever

for changing flow through the hydraulic lines that are

attached to the front loader attachment. With this

arrangement, the tractor power take-off can remain

running. The valve, when in neutral, dumps hydraulic

fluid back to the tank allowing the pump to run

continuously. It also opens when the pressure becomes

too high dumping fluid back into the tank.
An oil cooler with a temperature switch that turns the

cooler on when oil temperature reaches 140

F is

included to protect against overheating. The control box

will power the oil cooler.
This valve is particularly good for hydraulic cylinders on

equipment such as log splitters. It is not recommended

for operating equipment designed for continuous

operation such as hydraulic motors.

Solenoid Valve Option W/ Cooler

316-280A

Solenoid Valve Option With Cooler

Refer to Figure 3-4:

The solenoid valve is electrically activated from a control

box mounted near the operator or remotely located for

operating while standing near the equipment.
An oil cooler with a temperature switch that turns the

cooler on when oil temperature reaches 140

F is

included to protect against overheating.
The control box has one toggle switch for power on, one

for momentary operation, and one for continuous

operation.
Push and hold the yellow toggle switch to move a

hydraulic cylinder rod. Pull and hold the toggle switch to

move the cylinder rod in the opposite direction. Release

the toggle switch to stop cylinder rod movement.
Push blue toggle switch on to run hydraulic motor in one

direction. Pull blue toggle switch on to run hydraulic motor

in the opposite direction. Manually return toggle switch to

neutral (center) position to stop hydraulic motor

operation. The solenoid valve, when in neutral, dumps

hydraulic fluid back to the tank allowing the pump to run

continuously. It also opens when pressure becomes too

high dumping fluid back into the tank.

Manual Valve Option With Cooler

Figure 3-3

Solenoid Valve Option With Cooler

Figure 3-4

35622

35620

Summary of Contents for HRS3025













































Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands

Land Pride HRS3025, Operator'S Manual

Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands