Land Pride HRS3025 Operator'S Manual Download Page 34

Page: 34 / 44

Section 5: Operating Procedures

HRS3025 Hydraulic Reservoir System 316-271M

1/16/20

Table of Contents

Unhook Hydraulic Reservoir

Refer to Figure 6-2:

1. See

“Long Term Storage”

on page 33 if unit is to be

stored for a long time.

2. Park tractor on a level hard surface and with the

3-point lift lever, raise the reservoir high enough to

adjust the park stands down.

3. Without changing the 3-point lift height, shut tractor

down using

“Tractor Shutdown Procedure”

4. Adjust park stands to the minimum height available

that will allow the tractor to unhook from the unit. For

detailed instructions, see

“Park Stands”

on page 27.

5. Starting the tractor and lower the 3-point arms until

the park stands are supporting the unit.

6. Unhook hydraulic hoses from the attachment on the

tractor’s front loader and coil the hoses onto the

storage hooks located at the back of the reservoir.

At the tractor, pull back on the driveline pull collar and

hold while pulling the driveline from the tractor.

8. Collapse the driveline by pushing it towards the

reservoir.

9. Support the collapsed driveline off the ground to

keep dirt away from the pull collars and bearings.

NOTE:

Leave the 23'-9" long hydraulic hoses

attached to the reservoir. Disconnect the hoses from

the front loader attachment only.

10. Remove the hairpin cotter and top center hitch pin. If

provided, place center 3-point link in the tractor’s

holding clip.

11. Remove linchpins and lower 3-point hitch pins from

the lower 3-point lift arms.

12. Restart tractor and drive forward several feet while

making sure the lower 3-point arms do not catch on

the reservoir.

13. Place gear selector in park or set park brake, shut

tractor engine off, remove switch key, and dismount

tractor.

14. Reinstall hitch pins, linchpins, and hair pin cotters in

the Hydraulic Reservoir hitch for safe keeping.

Refer to Figure 5-1 on page 29:

1. Remove slow moving vehicle sign (#1) from

mounting bracket (#2).

2. Reinsert slow moving vehicle sign in mounting

bracket on the back of the tractor.

Unhook Hydraulic Reservoir

Figure 6-2

Quick Hitch Hook-up

Cat. I & II Top Center Link Clevis Pin

linchpins

Wire Retaining

Pins

Park Stands

Driveline

Hairpin Cotter

Lower 3-Point Hitch Pins

Cat. I
Clevises

Cat. II

Clevises

21422A

37298

Pull Collar

Top Center

3-Point Link

Power Take-off

Shaft

Drawbar

Lower 3-Point

Lift Arms

Summary of Contents for HRS3025













































Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands

Land Pride HRS3025, Operator'S Manual

Search results

Summary of Contents for HRS3025

Reviews:

Related manuals for HRS3025

Brands by name

Popular brands