Land Pride HRS3025 Operator'S Manual Download Page 17 | Manualshive

Page: 17 / 44

background image

Section 1: Assembly & Set-up

HRS3025 Hydraulic Reservoir System 316-271M

1/16/20

13

Table of Contents

No Valve With Cooler Option

The Hydraulic Reservoir System is supplied with one of

three valve options. See

“Valve Options”

complete description of valve options.

Refer to Figure 1-6:

1. Install oil cooler using instructions on page 12.
2. Rotate elbow (#14) forward as shown and tighten.
3. Apply Teflon tape to pipe threads on 1 5/16" MORB x

1" MNPT adapter (#13).

4. Remove plug from pipe nipple “A” and screw adapter

fitting (#13) to pipe nipple “A” until tight.

5. Screw spin-on filter head (#23) to adapter (#13) until

snug. Position filter head facing back as shown and

tighten adapter (#13) against filter head (#23).

6. Apply oil to both sides of square shoulder ring (#25).

Screw oil filter (#24) and shoulder ring (#25) onto

filter head (#23) until snug. Continue tighten oil filter

past snug by hand tightening filter 1/2 more of a turn.

7.

Screw O-ring end of 1 5/16" MJIC x 1 5/16" MJIC x

1 5/16" MORB tee (#16) to filter head (#23) until

snug.

8. Attach 1 1/16" MORB plug (#22) to top side of

pressure relief valve (#12) and tighten.

9. Attach 1 1/16" MORB x 1 5/16" MJIC adapter (#20) to

underside of pressure relief valve (#12) and tighten.

10. Screw tee (#21) to adapter (#20) until snug.

11. Attach mounting bracket (#1) to pressure relief

valve (#12) with 1/4"-20 x 1 3/4" GR5 cap

screws (#4), flat washers (#8), lock washers (#7),

and hex nuts (#5). Tighten hex nuts to the correct

torque.

12. Attach mounting bracket (#1) to reservoir tank with

3/8"-16 x 1" GR5 cap screws (#3), flat washers (#9),

spring lock washers (#10), and hex nuts (#6). Draw

hex nuts up snug.

13. Rotate tee (#21) until facing right as shown and

tighten against adapter (#20).

14. Screw hydraulic hose (#17) to pressure relief

valve (#12) until tight.

15. Adjust mounting bracket (#1) as needed and screw

hydraulic hose (#17) to tee fitting (#16) until tight.

16. Tighten mounting nuts (#6) to the correct torque.
17. Screw hydraulic hose (#18) to tee (#21) until tight.
18. Tighten tee (#16) to filter head (#23).
19. Screw 1 5/16" FJIC x 1 5/16" MJIC elbow (#15) to

tee (#16) until snug.

20. Screw 1" x 21" long hydraulic hose (#19) to

elbow (#15) until tight.

21. Loosen oil cooler bolts (#2) and adjust cooler as

need to attach hydraulic hose (#19) to oil cooler

port (#11). Tighten hose (#19) to port (#11).

22. Tighten elbow (#15) to tee (#16).
23. Tighten oil cooler bolts (#2) to the correct torque.

No Valve With Oil Cooler Assembly

Figure 1-6

30390

«
...
15
16
17
18
19
...
»

Summary of Contents for HRS3025













































Reviews:

No comments

Related manuals for HRS3025

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Tascam Pages: 128

Brand: ParaBody Pages: 6

Sportsound SSR-300

Brand: Daktronics Pages: 42

Brand: Hagie Pages: 141

Brand: Gardol Pages: 260

Brand: York Fitness Pages: 20

Brand: VBM Pages: 36

Brand: W&H Med Pages: 122

ENET-232 Series

Brand: National Instruments Pages: 105

Brand: PacBio Pages: 13

Brand: Pablo Pages: 4

Brand: PA Pages: 28

Brand: Pari Pages: 282

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands